Introducing the iFlight Chimera7 7" 6S LR HD Freestyle Quadcopter! This 7" long-range can fly places never seen before, and can carry bigger batteries to give you a longer flight time! The Chimera7 comes with the DJI FPV Digital HD System, and is mounted into a super-stiff frame for minimum resonance, and includes 2806.5 motors for maximum 7" prop control. You can fly big batteries (top-mounted) or even bigger batteries (bottom-mounted), 6 cells recommended, or 5 cells for slow cruising, but whatever style you fly - a Lipo or Lion pack will just do the job.
This freestyle quadcopter comes with a GPS functionality to help you find your way back when flying, and also Betaflight GPS Rescue mode (default OFF to prevent unexpected behavior. Setup instructions included).
Get incredible HD footage, all while capturing incredible footage at high speeds!
Features
6mm rigid arm design for more stiffness
Top- and bottom battery mount option
XING 2806.5 efficient wide stator motors
GPS pre-installed for more safety at a distance
GoPro TPU bottom stand (GoPro protector not included)
360° TPU protection, DJI cam protection, and antenna mounts
DJI FPV Air Unit, buttery-smooth 720p\120fps FPV feed (TPU soft mounted)
No props in view (DJI Air unit record in 1080p/60fps)
Battery voltage LED status light (illuminated IF logo on the bottom)
Specifications
Frame
Wheelbase: 320mm
Main body dimension: 285*199mm
Bottom to top distance: 20mm
Arm thickness: 6mm
Bottom plate thickness: 3mm
Top plate thickness: 2mm
Upper(middle) plate thickness: 3mm
Camera plate thickness: 3mm (included TPU inserts)
SucceX-D F7 V2.1 Stack (50A 4-in-1 ESC)
MCU: 216MHz STM32F722
Gyro：2x ICM20689
Baro: YES
Blackbox：32MB
Betaflight OSD: YES
BEC: 5V 2.5A / 9V 2.5A
Current sensor scale: 100
Inverter for SBUS input (UART2-RX)
Smart audio & Tramp VTX protocol supported
Beeper pad: Yes
RSSI input pad: No
UARTs：5
Motor outputs: 8
8 pin 4in1 ESC port (GND, VBAT, M1, M2, M3, M4, CUR, R5)
6 pin DJI Air Unit port (R1, GND, R2, T2, GND, 9V)
BLHeli32 Telemetry：RX5
Input voltage：recommended 2-6S, MAX 8S
Firmware Target: IFLIGHT_F722_TWING
Mounting pattern: 30.5*30.5mm φ4mm with Grommets φ3mm
Dimensions: 36*36mm
Weight: 7.5g
USB Type-C
SucceX 50A ESC
MCU: STM32F051
Up to 48kHz PWM frequency
Capacitance: 470uF/50V
Current Sensor: Yes
Input: 2-6S LIPO
Constant: 50A / Burst: 60A
BlHeli32 telemetry: Yes
BEC: No
Supports up to Dshot1200, Proshot, Oneshot, Multishot
Target: iFlight-BL32-4IN1
Weight: 14.4g
Mounting pattern: 30.5*30.5mm/Φ3mm
Dimensions: 43*39mm (including the power pads)
Additional Suggested Parts (Not Included)
DJI HD FPV Goggles
Radio Controller - Based on Receiver Choice
5S 3000mAh above (slow cruising)
6S 2500mAh above
GoPro Mounts
Package Includes
1 x Chimera7 frame
1 x GoPro TPU bottom stand incl. lock screw
1 x DJI FPV camera
1 x DJI FPV Air Unit Module
2 x Albatross LHCP RP-SMA 5.8g 150mm antenna
2 x Gemfan tri-blade 7040 props (Set of 4 - Color may vary)
4 x 20*250mm Microfiber PU Leather Battery Strap (Color May Vary)
Note:The DJI Remote Controller is recommended for beginners since you won't need to set up another receiver, but it is also optional in this BNF drone because it is NOT required in order to use the FPV system. If you don't choose to use the DJI Remote Controller, you can choose a receiver option for your transmitter and then bind to your own radio as usual.
