Happymodel Mobula6 1S indoor brushless tinywhoop racing drone is specially designed for indoor flying. Mobula6 is a highly integrated ultralight tiny whoop. It is small and portable, the weight is only 20g. It comes with the newly highly integrated integrated Crazybee F4 Lite flight controller with OSD, Dshot ESC, 2.4G SPI receiver, 5.8G VTX, 0802 motor KV19000 / 25000KV motor with 31mm propeller. Mobula 6 is your best choice for indoor flying this winter.
Specifications:
Item Brand: Happymodel
Item Model: Mobula6 1S 65mm Brushless whoop drone
Wheelbase: 65mm
Size: 80mm x 80mm x 37mm
Weight: 20g(without battery)
Features:
1.AIO 4IN1 Crazybee F4 Lite flight controller built-in 5.8G VTX
2.Extreme light 1S 65mm Brushless whoop only 20g
Runcam Nano3 The lightest 1/3 CMOS 800TVL Camera
3.Smooth and powerful
4.Compatible for 1S Lipo/LIHV
5.Camera Angle adjustable
Receiver option:
Internal SPI Frsky version (Compatible with ACCST D8/D16, Recommend D8 mode)
Internal SPI Flysky version(Compatible with AFHDS and AFHDS-2A Flysky transmitter)
Package includes:
Mobula6 1S 65mm whoop Drone Frame x 1
Crazybee F4 Lite flight controller x 1
SE0802 KV19000 or KV25000 brushless motor x 4
Gemfan 1219-3 Propellers(4cw+4ccw) x 1
Runcam Nano3 1/3 CMOS 800TVL camera x 1
Frsky SPI D8 or Flysky SPI Receiver x 1
5.8G 25mw 40ch vtx (Flight controller built-in) x 1
1S Lipo/LIHV USB Charger x 1
Propeller disassemble tool x 1
Note: The 1S 300mah 30C Battery is not included due to the shipping problem, you need to purchase it separately.
Spare parts specifications:
Motor |
Mode: SE0802 19000KV or KV25000
Configu-ration:9N12P
Stator Diamter:8mm
Stator Length:2mm
Shaft Diameter:Φ1mm
Motor Dimension(Dia.*Len):Φ10.5mm*14.9mm
Weight(g):1.9g
No.of Cells(Lipo):1S only |
| Propellers |
Gemfan 1219-3
Center Thickness:5mm
Prop Disk Diameter:31mm
Center Hole Inner diameter:1.0mm
Weight:0.28g |
| Flight controller |
(Frsky SPI RX version) CRAZYBEE F4 Lite Frsky version Firmware target: CrazybeeF4FR
(Flysky SPI RX version) CRAZYBEE F4 Lite Flysky version Firmware target: CrazybeeF4FS
MCU:STM32F411CEU6 (100MHZ, 512K FLASH)
Sensor: MPU-6000(SPI connection)
Board size: 28.5 * 28.5MM
Power supply: 1S battery input (DC 2.9V-4.35V)
Built-in 5A(each) Blheli_S 4in1 ESC Dshot600 ready
Built-in Betaflight OSD(SPI Control)
Built-in 5.8G VTX
Built-in SPI Frsky/Flysky receiver
Built-in 5V 1A BEC
Built-in voltage detection |
| Onboard 4in1 ESC |
MCU upgraded to EFM8BB21
Power supply: 1S LiPo/LiPo HV
Current: 5A continuous peak 6A (3 seconds)
Support BLHeliSuite programmable
Factory firmware: O_H_5_REV16_7.HEX
Default protocol: DSHOT600 |
| Onboard Frsky SPI D8 receiver Version |
SPI BUS receiver Frsky D8 compatible
Compatible Non EU transmitter D8 model
Channels: 8ch
Failsafe support
No ground interference ( Transmitter and receiver 1 m from the ground): 100m~200m |
| Onboard Flysky SPI receiver Version |
SPI BUS receiver
Protocol: AFHDS and AFHDS-2A Switchable
Channels: 8ch(AFHDS) or 14ch(AFHDS-2A)
No ground interference ( Transmitter and receiver 1 m from the ground): 100~200m
Failsafe support |
| Onboard 5.8g VTX |
Output power: 25mw
Frequency: 40CH
Input voltage: 3.3V 5.5V
Current consumption: 300mA(type)
Frequency: 5.8GHz 5bands 40 channels
With Race band
Smartaudio ready |
| Runcam Nano3 |
Model: RunCam Nano 3
Image Sensor: 1/3" CMOS
Horizontal Resolution: 800TVL
Lens : 2.1mm(M8) FOV 160°
Signal System: PAL/NTSC Non Switchable
S/N Ratio: >50dB
Electronic Shutter Speed: Auto
Auto Gain Control (AGC): Auto
Min. Illumination: [email protected]
D-WDR: Auto
Day/Night: Color
Power:DC 3-5.5V
Current: 110mA@5V [email protected]
Housing Material: ABS
Net Weight: 1.2g
Dimensions: L14mm*W14mm*H9mm |
| Lipo Battery |
Capacity:300mAh
Voltage:3.8v
Continuous Discharge Rate: 30C
Size: 57mmx12mmx7mm
Weight: 8g
Connector: PH2.0 |
