Due to the lack of the chips, this flight controller will not be available again this year. You can check the V5 + here.
CUAV V5 nano is an autopilot flight controller for space-constrained applications, designed by CUAV in collaboration with the PX4 team.It is compatible with PX4 and Ardupilot open source platform firmware, which can meet different uer needs. The autopilot is small enough to use in 220mm racing drones, but remains powerful enough for most drone use.It is suitable for fixed wing, helicopter, multi-rotors, VTOL, UAV drones and etc.
Main Features:
- Compact but powerful V5 nano flight controller + NEO GPS
- Support for hardware on open source platform PX4 and Autopilot
- Suitable for fixed-wing drones, helicopters, multicopters, FPVs, VTOL, Unmanned UAV and etc
- High Performance: Equipped with STM32F765 microprocessor, features 216MHz main frequency, 2M flash and 512K SDRAM. There are four groups of isolation chips and a MS5611 high-precision air gauge.
- Easy to install and dismantle with 2.6mm spacing between IO pins.
- Real-time Data Monitor: Five groups of built-in sensors enhance its safety and stable performance. There are ICM-20689 accelerometer and gyroscope, ICM-20602 accelerometer and gyroscope, BMI055 accelerometer and gyroscope, IST8310 magnetic compass and MS5611 air gauge.
Specifications:
Hardware Parameters:
- Main FMU Processor: STM32F765(32-bit, 216MHz, 2MB flash, 512KB RAM)
Sensors:
- Accelerometer: ICM-20602/ICM-20689/BMI055
- Gyroscope: ICM-20602/ICM-20689/BMI055
- Magnetometer: IST8310
- Air Gauge: MS5611
Interfaces:
- UART Ports: 5
- I2C Ports: 4
- CAN: 2
- ADC: 2
- PWM Output: Up to 11
- PWM Input: 4
- PPM input: 1
- DSM/SBUS/RSSI: 1
- Power model 1: 1
- Power Model 2: 1
- Safety Switch: 1
- Buzzer: 1
- USB-TYPE-C: 1
- TF slot: 1
Supported Function:
- Firmware: PX4/Ardupilot
- Model: Multirotors/plane/helicopter/VTOL/UAV/Rover, etc.
Working Conditions & Physical Parameters:
- PM Working Voltage: 4.5 to 5.5V
- USB Voltage: 5V±0.25V
- Servo Rail Input: 0 to 36V
- Working Temperature: -40 to 85°
Weight & Dimensions:
- Dimensions: 40 x 60 x 17.5mm
- Weight: 40g
Package Included:
- 1 x V5 nano Flight Controller
- 2 x Dupont Cables
- 1 x ADC6.6 Cable
- 2 x I2C/CAN Cables
- 1 x SBUS Signal Cable
- 1 x RSSI Cable
- 1 x DSM Signal Cable
- 1 x ADC3.3 Cable
- 1 x Debug Cable
- 1 x Safety Switch + Cable
- 1 x Voltage Current Cable
- 1 x PW-Link Module + Cable
- 1 x Power Suppl Module
- 1 x 16GB Memory Card
- 1 x I2C Expansion Board
- 1 x TTL Board
CUAV NEW Ublox NEO M8N GPS Module integrates dual-mode GNSS, safety switch, RGB status light and Electronic Compass, it is specially designed for Pixhack V5/V5 Plus flight controllers.
The built-in dual mode GNSS module provides high sensitivity and minimal acquisition time while maintaining low system power and simultaneous acquisition and tracking of different GNSS systems: Parallel receiv GPS (QZSS) and GLONASS OR BeiDou, or receiv both GLONASS and BeiDou. Built-in SAW and LNA with advanced RF architecture and interference suppression ensure optimal performance in a weak GPS signal enviroment.
Specifications:
GPS Location: U-BLOX M8N
RGB Status light: NCP5623C
Compass: IST8310
Buzzer: Passive buzzer
Safety switch: Physical buttons
Accuracy: 3D Fix
Update rate: 10Hz(Max)
Acquisition: Cold start 26S/Hot start 1.5S/Aided start 2S/ Reacquisition 1S
Receiver Type: 72 Channels (GPS/QZSS L1 C/A, GLONASS L10F, BeiDou B1I, Galileo E1B/C, SBAS L1 C/A: WAAS, EGNOS, MSAS, GAGAN)
Sensitivity:
Tracking&Navigation -167dBm
Cold start: -148dBm
Hot start: -156dBm
Reacquisition: -160dBm
Functional:
Advanced jumping
Fast search satellite speed
Security and integrity protection
Receiving up to three GNSS at the same time
Input voltage: 5V
Operating temperature: -10 ~ 70°c
